STIHL TS410 Parts

The TS 410 STIHL Cutquik® Cut-Off Saw is a really nice machine for professional use and boasts some great specs and cool features.

Specifications of the STIHL Saw TS410

When you look at the Stihl ts410 manual, you see the following specs:

• DISPLACEMENT 66.7 cc (4.07 cu. in.)
• ENGINE POWER 3.2 kW (4.4 bhp)
• WEIGHT* 9.4 kg (20.7 lbs.)
• FUEL TANK CAPACITY 710 cc (24 oz.)
• ENGINE SPEED 9,000 rpm (Elec. Gov.)
• MAX. SPINDLE SPEED 5,350 rpm
• ARBOR SIZE 20 mm
• MAXIMUM WHEEL SIZE 300 mm (12")
• MAXIMUM CUTTING DEPTH 100 mm (3.9")
• POWER SOURCE Gas

Let's talk about some of the STIHL TS410 parts, where they are located, and what they do.

Noteworthy Stihl TS410 Parts List

A new Stihl ts410 parts list will have features that make this cut-off machine easy to use and maintain.

• Reduced-Emission Engine Technology for zero or low exhaust emissions.
• IntelliCarb™ Compensating Carburetor to automatically adjust the air/fuel ratio when the air filter becomes restricted or partially clogged and maintains the engine’s correct RPM. It uses air from the clean side of the air filter to control the diaphragm and flow of fuel. As the air filter becomes dirty and less air is available for the carburetor, the IntelliCarb™ system adjusts the fuel flow to compensate for the decrease in air flow. This is in contrast to typical carburetors that utilize this air from the “dirty” side of the air box. If you need a new carb, ArborTec has your replacement carburetor for Stihl TS410. This carb replaces Stihl part no. 4238-120-0600.
• X2 Air Filtration System allowing air filters to last up to a year. Outside air enters the system in a swirling motion, removing 80% of dust particles. This pre-cleaned air is then routed through the primary and secondary air filters before being sent into the engine. The X2 Air Filtration System is virtually maintenance free and maintains an incredible 99.96% cleaning efficiency.
• Semi-Automatic Belt Tensioning increases the service life of the belts and shaft bearings. It is a nut that allows for easy adjustment of drive belt with a couple of twists.
• Anti-Vibration System for minimizing the vibration levels of the saw.
• Spark Arrestor Muffler has large baffles which reduce noise level, and contains a screen designed to reduce the emission of sparks.
• Intergrated Water Supply Tube

(Note: TS420 Stihl cut off saw parts are all the same as the TS410 parts, except where it comes to the cutting wheels. The main difference between the TS410 and TS420 is the size of the wheel guard and cutting wheel.)

Among the very important stihl ts410 parts are its air filter system. To inspect or replace the filter, remove the cover at the back of the saw behind the top handle. These filters require no maintenance or cleaning. You simply replace 'em if and when you detect a loss of engine power.

The Stihl saw ts410 has a purge pump or primer that helps with easier starting by filling the carburetor with fresh fuel, while purging warm fuel out of the carb. Carburetors also have adjustment screws that you can access through the housing. Read the manual for proper adjustment requirements.

There's a decompression valve button relieves some compression from the cylinder so that the saw will be easier to crank. By the way, ArborTec has a replacement Stihl TS410 cylinder kit (replaces original Stihl part #4238 020 1202) for you here. If you just need the piston for a ts 410, then here's your replacement Stihl TS410 piston kit that replaces original part #4238 030 2003.

Another thing that helps start the ts410 is the throttle lock thumb switch on the front of the handle. With this, you can lock the gas flow on for cold starting, but you should not operate the saw with this locked. Of course there's a choke lever for starting a cold ts 410 also.


The throttle trigger interlock is on the top of the saw's handle. The palm of the trigger hand covers and depresses it to keep the saw running. Once you let go, the saw will stop. This is a safety device to prevent trigger action when not firmly gripped. The trigger cannot be depressed to rev the engine unless this throttle trigger interlock is depressed. For starting, you squeeze the throttle interlock and throttle at the same time, and then lock the thumb switch in the ON position. Then the throttle will remain in a partially pressed position even when you let go.

When starting a Stihl ts 410 cold, close the choke. If the saw is still warm after a previous run, you can use the choke half way. Press the compression release button, and once the engine has fired, it'll close itself. Press the purge button a few times until you see it fills with fuel. Now that the fuel lines and carb have fresh and cool fuel, it should start easier. The first time the machine attempts to start, push in the compression release button again and move the choke to the open position so that you don't flood the machine on your next pull with choke in full closed position. (Sometimes starting problems indicate a need for a new Fuel Filter For Stihl TS410 Replaces 0000-350-3500.)

Here's a trick regarding the TS410 Stihl starter rope. Don't let it go after a pull so that it snaps back or else the grip can break. If you break yours, click here to buy a replacement Stihl recoil starter assembly. This replaces original part #4238 190 0300.

To help reduce fatigue for the operator, Stihl TS-410 has anti vibration systems to absorb shaking.

One of the interesting little stihl ts410 parts is found at the muffler. Here you'll see a spark arrestor screen.

Every Stihl ts 410 has a water attachment to rinse or wash away airborne dust and particles.

To adjust the tension of the drive belt, you'll find a tensioning nut to properly adjust the tension of the drive belt to the cutting wheel.

TS 410 STIHL

If you have a ts 410 stihl, you know how good it is. If you seek a great professional, easy to handle cut off saw, the ts 410 STIHL should be on your list.

For Stihl TS410 parts to fix 'em like new, go to ArborTec. We've linked to several parts above, and we also probably have the best prices on: replacement crankshaft for Stihl TS 410 here. This crankshaft replaces OEM part #4238-030-0400.

Clutch that fits Stihl TS-410 and replaces #1125-160-2005.

Here's the general Stihl TS410 parts page.

Hope this helps you get to know your saw and repair it if needed.